Ideal Patio Pet Door - Super Large Pet Opening
15"w x 20"h
TALL adjustment height: 93 3/4" to 96 1/8"
Product Dimensions
|
Pet Opening |
15" x 20" |
Overall Panel Width |
19 1/2" |
Rises Available |
2.5", 4" & 8" |
TALL height range: 93 3/4"- 96 1/8"
|
Ideal Patio Pet doors are a good rugged, utility model insert. They come with a limited lifetime warranty, and you can replace the flaps whenever needed to ensure the pet opening maintains a good seal. The units are light-weight, so that if you want to remove them, anyone can lift them out. This can be important especially if you do not have much room in your sliding door opening to begin with.
Note: Many customers prefer this insert to higher costing panels because they can easily put-in and take-out this panel very easily. Often the dual pane units are much heavier due to the glass. If the weather or temperatures become too severe, this unit can be removed and set off to the side with very little effort. Chances are your pet would not be going outside it the weather were extreme.
*Panel width is approximate
You know your pet best - double check the opening and rise selected to ensure best fit
Ideal Pet Patio Door Tall - Super Large
"Tall" Height Range 93 3/4" to 96 1/8"
*Panel Width - 19"
Slide-In locking Panel Included
|
Pet
Opening |
Rise Options
|
Video |
Install |
How to
Replace
Flaps |
Hassle Free
Returns
Click Below |
Get
Adobe
Reader |
15" width
x
20" tall
|
2.5", 4", 8", 12"
Rise selected
will raise the
pet opening
by that amount
|
|
|
|
|
Adobe Reader Required
to view PDF files |
Notes: If your Sliding door opening height measurement is very close to minimum of this inserts range then you may want to consider a shorter height range range to ensure this unit will contract enough to fit into your track. Call us with any questions 1-800-829-7876 .
How to measure for a Patio Pet DoorNo Re-stocking fees for this Product |
Features:
Pet Opening 15"w x 20"h: Appropriate for larger sized dogs up to 120 lbs.
Rise Options: This unit comes standard with a 8 " high step over rise, optional 2.5 ", 4" & 12"custom rises are available.
Weatherstripping: Included foam bumper and vinyl draftstopper for gap between slider and fixed panel.
Adjustable height range 93 3/4" to 96 1/8": The top section floats on two tension rods. You simply compress the top and fit it in the track, then release the top. A thumb bolt on either side near the top secures the top section so the Patio Pet Door cannot be removed from the outside. It installs and is removed in seconds.
No tools required to install the patio insert.
Push Pin Lock included: We strongly suggest chocking the door with a stick as this immobilizes your slider. We also have accessory sliding door locks that you may use.
Installation: Most customers install next to the sliding door. Can be mounted on the fixed side of the slider. Some fixed windows are molded in and for those, this will not work. Others, have stoppers either in the bottom or top track that keep the fixed side stationary. If you remove the stoppers, you can pull out the fixed side far enough to accept the patio insert.
Security Panel: Includes a slide in locking panel to use when you want to "lock off" the pet opening.
Ideal Pet Patio Pet Door Installation Instructions
Release automatic height adjustment by
turning knobs located near the top of the panel counter-clockwise and pressing.
Height adjustment panel should fully extend upward (pull upon the panel if
necessary).Open sliding glass/screen door insert panel with knobs facing inside. Place top edge into top track of
sliding glass/screen door. Lift up and swing lower portion of panel either onto
ridge, in bottom inside track or screen track.
Slide
the panel against door jamb and make sure that top is fully extended, not tilted
to one side.
Hand-tighten
knobs by turning clockwise to lock the panel in place.
To permanently install, you may screw through the aluminum fins that protrude
on the existing frame of your door. Drill through the fins into the panel.
Install two screws in the top and two in the side by the bottom of the panel. Do
not put any screws into the frame by the glass as breakage may occur.
Optional permanent placement for fixed panel sliding door. Remove screws that
hold fixed glass panel in place and slide over. Insert the panel and re-fasten
fixed glass panel.
Installing Security Lock (Optional)
(Placement Options-see above)
With sliding door in closed position, place lock in desired location and bolt
in the retraced position, pointed toward the sliding glass door or stationary
window rail. Leave approximately 1/8” clearance between bolt tip and aluminum
rail.
Holding lock firmly in place, mark screw holes and center of bolt in rail of
sliding door or stationary window.
Drill two 5/32” holes for mounting screws and a 3/8” hole for locking bolt.
Caution: Do not drill into glass.
With sliding door in the closed position (with patio door installed), mark
position for second set of holes.
Repeat above instructions Caution: Do not drill into glass.
Weather Stripping Placement
There are two pieces of weather stripping included in this package. A thin, wide
draft-stopper with an adhesive strip that attaches to the back side of
the sliding door that extends to the glass of the fixed window.
The
other thin piece of weather stripping is the foam bumper, also with an
adhesive backing, it attaches to the panel to provide a better seal when the
sliding door closes against the panel.
;){kind=icon}
Now Shipping to 34 countries!
